Can this 24V PoE powered switch work with a standard PoE switch as the power source?

Yes, if the upstream switch provides passive PoE on pairs 4/5+ and 7/8- (non-standard). Standard IEEE 802.3af/at switches use different pin pairs, so they won’t power this switch directly unless the uplink port also supports passive PoE on those pairs. You may need a passive PoE injector or a dedicated 24V DC supply.

What kind of devices can I connect to the PoE output ports?

Any device that accepts 24V passive PoE on pairs 4/5+ and 7/8-—typically older IP cameras, some outdoor access points, and certain IoT sensors. Check your device’s spec: if it expects 48V standard PoE, it won’t work directly with this switch.

How do I set up the one-key VLAN isolation?

Just toggle the VLAN switch on the case. When the VLAN mode is on, ports 2 through 8 can only talk to port 1 (the uplink). They cannot see each other. Turn it off for normal switching where all ports communicate freely. No software needed.

Can I power this switch with a 24V battery or solar system?

Absolutely. The input voltage range is 15–56VDC, so a 24V battery bank works perfectly. Just connect the positive and negative to the DC input terminals (or barrel jack, depending on your model). The switch also provides 12V and 5V outputs for other low-power gear.

How many devices can I power simultaneously with this 24V PoE switch?

The switch itself consumes ≤2W, and each PoE output port can deliver power based on your upstream supply. Since it’s passive PoE, the total power budget depends on your input source and cable length. For example, with a 24V/2A supply, you can typically power several low-power cameras (each drawing 3-5W) on short cable runs. For high-power devices, consider a higher-current supply (e.g., 24V/5A).

Is this switch plug-and-play? Do I need to configure anything?

Yes, it’s fully plug-and-play. No IP address, no web interface, no CLI. Just connect the cables and power, and the switch starts forwarding traffic. The only optional tweak is the VLAN toggle—set it if you need isolation.

What cable length is supported for 100Mbps PoE?

100Base-TX works reliably up to 100 meters over Cat5e or better. For 10Base-T (10Mbps), the distance can go up to 250 meters. PoE power delivery over the same cable will also be limited by the cable’s resistance—longer runs may drop voltage, so keep runs under 100m for best performance.

Can I mount this switch outdoors?

The plastic housing is rated for -20°C to +60°C, but it’s not weatherproof (no IP rating). For outdoor use, place it inside a weatherproof enclosure. It’s fanless, so no moving parts to fail—good for dusty or semi-outdoor locations like a garage or shed.

What does ‘Reverse PoE’ mean?

Reverse PoE means the switch can be powered over the Ethernet cable from a PoE source (instead of powering other devices). In this switch, the uplink port (port 8) accepts PoE input using the same unused pairs. So if you have a PoE source upstream, you don’t need a separate DC adapter at the switch location.

How do I know if my device supports the PoE pinout used by this switch?

This switch uses pins 4/5 (positive) and 7/8 (negative) for both input and output PoE. Most passive PoE cameras and radios that operate on 24V use that same pinout. Check your device’s manual or look for a label that says ‘Passive PoE 24V (4,5+ / 7,8-)’. If your device uses pins 1/2+ and 3/6- (like standard 48V PoE), it won’t work directly.

Ethernet Switches

PoE Switches

Industrial Switches

Media Converters

L2+ Cloud & Managed PoE/Non-PoE Switches

Gigabit Cloud Managed PoE Switches with 4/8/16/24 port options support dual APP cloud and web management, one-click cloud & VLAN isolation, 6KV full surge protection, and flexible desktop/wall/rack mounting for versatile industrial networking.

Click to know more

L3 Industrial Managed PoE/Non-PoE Ethernet Switches

Click to know more

DPM Series(Digital Power Meter PoE Switches)

This series consists of innovative switches independently developed by WangLink with proprietary patents, thoroughly engineered for long-term stability and reliability. Equipped with exclusive power monitoring technology, the product line supports real-time viewing of overall device operating power data, enabling intuitive visualization of power supply load and power consumption status. This facilitates rapid troubleshooting of overload and power supply abnormalities, greatly reducing network operation and maintenance workload, and ensuring consistent and stable operation of the entire system.PoE Switches – DPM Series(Digital Power Meter PoE Switches)

Click to know more

Reverse PoE Switches

Reverse PoE switches deliver power and data over long distances, ideal for IP cameras and remote security setups. Our range includes outdoor, industrial, and managed models from Wanglink factory, with detailed specs and solutions for surveillance networks.

Explore All Reverse PoE Switches

showcase of Unmanaged 24V PoE Powered Switch, 7-Port Fast Ethernet + 1 Gigabit Uplink, Reverse PoE, Desktop/Wall-Mount for IP Cameras and Remote Sites

Unmanaged 24V PoE Powered Switch, 7-Port Fast Ethernet + 1 Gigabit Uplink, Reverse PoE, Desktop/Wall-Mount for IP Cameras and Remote Sites

Name: Unmanaged 24V PoE Powered Switch, 7-Port Fast Ethernet + 1 Gigabit Uplink, Reverse PoE, Desktop/Wall-Mount for IP Cameras and Remote Sites
Brand: WangLink
SKU: SL710RP-1S

A 24V PoE powered switch that delivers power over unused cable pairs. Ideal for hard-to-reach locations—simplifies wiring, cuts power supply costs, and runs reliably in tough environments.

SL710RP-1S

Port Description

7 ports 10/100Base-TX (PoE out) + 1 port 10/100/1000Base-T (PoE in). All RJ45, auto-MDI/MDI-X, half/full duplex.

Powered via PoE input on uplink port – no need for a local power adapter in many setups
Delivers 24V passive PoE on 7 ports over unused pairs (4/5+, 7/8-), perfect for compatible IP cameras and access points
One-key VLAN isolation: isolate downstream ports for security or traffic segmentation without logging in
Wide DC input range (15-56V) plus two auxiliary DC outputs (12V and 5V) for powering edge devices
Fanless plastic design rated for -20°C to +60°C, reliable in dusty or high-temperature environments

Datasheet

Request a Quote